← View All Updates



Over $200k!

Dear backers,

We are ecstatic to have passed $200k in our campaign to bring Novena to the world! Thanks to all our existing backers and fans for all the support they have lent to our project – without your help we wouldn’t be here.

We now have $50k left to raise in 19 days; even more if we’re to hit any of our stretch goals, which include hot topics like 3D graphics drivers and hardware breakout boards. Please keep up the good work and remind your friends and colleagues about why open hardware matters, how much fun it can be, and how hackable platforms like ours can accelerate research and development.

To keep up with the latest press we’ve been getting, or to introduce your friends to Novena, check out these two recent articles:

Community is the lifeblood of any open source project, so we can’t make it without your help. Thank you again!


xobs and bunnie

$783,382 raised

of $250,000 goal

Funded! Order Now

May 18 2014

funded on





Product Choices


Just the Board

For crafty people who want to build their case and define their own style, we'll deliver to you the main PCBA, stuffed with 4GiB of RAM, 4GiB microSD card, and an Ath9k-based PCIe wifi card. Boots to a Debian desktop over HDMI.


Hacker Case Kit

The barebones hacker case kit! It'll give you the structure on which to build your custom Novena set-up using your main board. Grab some mounting screws from the hardware store, and you're ready to go.


General Purpose Breakout Board (GPBB)

Breaking out all the goodies, this 40 pin header allows you easy access to the Novena Spartan-6 FPGA. The GPBB buffers 16 FPGA outputs and 8 FPGA inputs to be compatible with either 3.3V or 5V, gang-selectable via software. It also provides six 10-bit analog inputs (up to 200ksps sample rate) and two 10bit analog outputs (~100ksps max rate), all broken out to an easy-to-use 40-pin male 0.1” dual-row header. The board was created as a stretch goal in the original Novena crowdfunding campaign.



Overstock of the custom-manufactured batteries for the campaign - these are 5000mAh 3-cell lithium battery packs that fit especially well into the Novena desktop or laptop case. *International shipping not available for this item.


Battery Holder

A holder for the standard Novena battery pack mentioned above. Holds the battery nicely in the Peek array of the injection-molded case. Has a 4mm bullet connector.


eDP Adapter Board

This adapter board is a bridge between the LVDS port on the main board and the eDP connection for the LCD screen. It has hole placements to be secured directly over the main board using the appropriately sized M2 screws. See here for more details.


LCD Screen

This is the same screen as that used in the desktop and laptop Novena configurations. It is a 13.3" amorphous silicon TFT active matrix IPS LCD at 1920 x 1080, 166 ppi, 350 cd/m2 luminance at max brightness, 700:1 contrast ratio (typical), 14ms TR, 11ms Tf (typical) response time, and a wide viewing angle of approximately 89 degrees vertically or horizontally in any direction.


AC Adapter

AC power supply for Novena configurations, with a US plug. 100-240V input at 50/60Hz and 1.5A. 18V output at 3.47A. Branded with the Novena logo!


Cable Clips (Set of 3)

Helping you keep your project tidy, these cable ties screw (M2.5 screws with washers - not included) into the Novena case "Peek Array". Domestic shipping included.


Sutajio Kosagi

Sutajio Ko-usagi supports and produces open hardware products designed by bunnie and xobs.



Sean Cross


Mottweiler Studio

Heirloom laptop design and fabrication

AQS Inc.

Contract Manufacturer


Video Editing

Subscribe to receive the Crowd Supply weekly newsletter, highlighting the latest creators and projects: